LORD 360

Harmonization Code : 3506.91.90.99 | Prepared glues and other prepared adhesives, not elsewhere specified or included; products suitable for use as glues or adhesives, put up for retail sale as glues or adhesives, not exceeding a net weight of 1 kg ; Adhesives based on polymers of headings 3901 to 3913 or on rubber; Other ; Other

LORD 360

Main features

  • 1:1 Equal-Volume Mixing
  • 5-10 Minute Handling Strength
  • Minimal-Sag Vertical Application

Product Description

LORD 360-A/360-B is an equal-mix, two-part epoxy adhesive system for bonding scuffed SMC, FRP, wood and plastics. The 1:1 volume mix has a typical 2-4 minute working time at 24 deg C and reaches handling strength in 5-10 minutes between 18 and 38 deg C. For general use, a 0.51-0.76 mm adhesive film is recommended, and the mixed material shows minimal sag on vertical or overhead surfaces. Full cure strength develops in approximately 24 hours at room temperature or in 20-30 minutes at 82 deg C.

Key features

  • Equal-Ratio Mixing: Resin and hardener are mixed at a 1:1 ratio by volume.
  • Assembly Handling: The mixed adhesive reaches handling strength in 5 to 10 minutes between 18 and 38 deg C.
  • Vertical Application: The mixed paste shows minimal sag on vertical and overhead surfaces.

Applications

Scuffed SMC, FRP, wood and other plastics, including sign-assembly applications.

Product Family

LORD 360

Loading pricing…
TDS, SDS & Technical Documents

Technical Specifications

General Properties
Appearance
Appearance at room temperature.
Tan to Light Brown Paste/Light Grey to Tan Paste
Density
Volumetric mass per unit
1438 -1618/1019 -1138 kg/m3
Mix Ratio
The amount of a constituent divided by the total amount of all other constituents in a mixture
1:1
Solids
100 %
Physical Properties
Viscosity
Viscosity is a measurement of a fluid’s resistance to flow. Viscosity is commonly measured in centiPoise (cP). One cP is defined as the viscosity of water and all other viscosities are derived from this base. MPa is another common unit with a 1:1 conversion to cP. A product like honey would have a much higher viscosity -around 10,000 cPs- compared to water. As a result, honey would flow much slower out of a tipped glass than water would. The viscosity of a material can be decreased with an increase in temperature in order to better suit an application
90,000 -180,000/40,000 -180,000 mPa.s
Thermal Properties
Flash Point
The flashpoint of a solvent is the lowest possible temperature at which it can vaporize to form an ignitable vapor. Flashpoint is often confused with “autoignition temperature”, which is the temperature at which a solvent ignites without an ignition source.
93 °C

Additional Information

Technical properties

As-supplied / before-processing properties

Component values are shown separately; mix and timing values apply to the combined LORD 360-A/360-B system.

PropertyValueUnitMethod / condition
LORD 360-A viscosity90,000-180,000cPTypical; Brookfield HBF, Helipath, 5 rpm; 25 deg C
LORD 360-B viscosity40,000-180,000cPTypical; Brookfield HBF, Helipath, 5 rpm; 25 deg C
LORD 360-A density1,438-1,618kg/m3Typical
LORD 360-B density1,019-1,138kg/m3Typical
Mix ratio1:1by volumeResin to hardener
Working time2-4minutesTypical; 54 g mass at 24 deg C
Time to handling strength5-10minutesTypical; 18-38 deg C
Shelf life2yearsOriginal unopened container at 16-27 deg C

Leading Brands Trust in Our Products and Services

Products that Perform| Knowledge that Serves| Service that Delivers